 |
 |
|
|
HANDY2 - HANDY4
Serialized and Programmable Rolling Code Transmitters
A Giugiaro’s design. Basic lines and a transparent insert
showing the technology of V2 Elettronica.
The operating frequency is 433.92 MHz, with 4.5 million codes,
and all this has been manufactured in an extremely small size.
It is available in both 2-and 4 key versions, namely, HANDY2 and
HANDY4. It is possible to activate 3 channels (HANDY2) and 15
channels (HANDY4) by use of key combinations.
STANDARD programming by means of PROG2 (PROG TX connector).
FAST programming by means of FASTPROG: enabling you to programme
your transmitter without taking it out of its housing.
It is also available in uncoded programmable versions HANDY2P
and HANDY4P, as well as the standard pre serialized versions.
|
| |
 |
TSC-4
Serialized and Programmable Rolling Code Transmitters
4-channel 433,92 MHz miniaturized transmitter serialized by V2
Elettronica: each transmitter is identified by a univocal alphanumeric
code (label code), which allows personal identification of any
single user.
It is available also in the programmable TSP-4
version: thanks to the portable PROG2 programmer or WINPPCL software,
new “label codes” for the programming of blank transmitters
can be automatically created.
CATALOGUE
|
 |
TRC-4
Serialized and Programmable Rolling Code Transmitters
4-channel 433,92 MHz miniaturized transmitter serialized by V2
Elettronica: each transmitter is identified by an univocal alphanumeric
code (label code), which allows personal identification of any
single user.
It is also available in the programmable TRP-4 version:
thanks to the portable PROG2 programmer or WINPPCL software, new
“label codes” for the programming of blank transmitters
can be automatically created.
CATALOGUE
|
 |
TMU99
99-channel transmitter
The TMU99 transmitter has been created to control a large number
of users by means of one transmitter only. It is equipped with:
Two-digit and backlighted display to simplify selection
and display of the chosen channel.
Down battery indication.
Stand-by mode operation to minimize consumption: it will self-switch
off 5 seconds after the last key pressure.
Possibility to define the most used channel.
Keyboard lock function.
CATALOGUE
|
 |
TTNR433PP
Wireless digital selector
The TTNR433PP wireless digital selector is a transmitter that
replaces the usual key selector.
It does not need any external electric connection.
It can be activated by entering a personalized combination on the
special alphanumeric backlighted keyboard.
It has the same range as a Personal Pass remote control.
It is powered by means of an internal 9 Volts battery.
It has a down battery signal that is an acoustic alarm.
CATALOGUE
|
 |
WALLY1 - WALLY2 - WALLY4 - WALLY4PLUS
12-24V Outdoor receivers
A Giugiaro’s design. A special attention to the shape, which
is harmonized with transmitter Handy’s lines, so to create
a couple where technology gets married with aesthetics.
The operating frequency is 433.92 MHz. There are 1, 2, 4 programmable
channels with three functions available: monostable, step by step
and timer.
It is a leader product thanks to its functionality and safety,
equipped with a memory that can recognize up to 240 codes with
regard to standard versions (WALLY1, WALLY2, WALLY4).
It is also available in the 4-channel version called WALLY4PLUS,
which can store up to 1008 different codes.
Series WALLY, ready for those applications where DUAL BAND technologies
are used, includes now the following monofrequency receivers:
- WALLY1/434, WALLY2/434,WALLY4/434: 434.15 MHz receivers with
240 available codes to be stored.
- WALLY4/434P: 434.15 MHz receiver with 1008 available codes to
be stored.
- WALLY1/868, WALLY2/868, WALLY4/868: 868.3 MHz receivers with
240 available codes to be stored.
- WALLY4/868P: 868.3 MHz receiver with 1008 available codes to
be stored.
WALLY is equipped with an extractable terminal board,
to change data inside the receiver, which allows a fast work without
cutting the wire connection.
Self-learning operation of the transmitters by radio: the procedure
that allows to store new transmitters by radio, sequentially and
without taking the receiver out of the installed system.
Sequential programming of the transmitters.
ROLLING CODE mode.
Built-in aerial.
CATALOGUE
|
 |
MR1
433,92 MHz super-heterodyne receiver module with memory for the following
control units: PD8 (integrated to the gear motor GOLD230V-D), PD9
and CITY1.
It is possible to store up to 240 different codes with self-learning
mode.
Series MR1, ready for those applications where DUAL BAND technologies
are used, includes now the following monofrequency receivers:
- MR1/434: 434,15 MHz plug-in receiver
- MR1/868: 868,3 MHz plug-in receiver
Sequential programming of the transmitters.
Self-learning operation of the transmitters by radio.
ROLLING CODE mode.
|
 |
RXD1PP - RXD2PP
Plug-in receivers
433,92 MHz single or double channels plug-in receiver equipped with
a 10-pole molex connector and outputs which can be set up on a customer’s
request.
Possibility of storing up to 83 codes of different transmitters
by self-learning mode.
Three different functions can be programmed for the outputs: monostable,
bistable and timer.
Possibility of erasing the stored transmitters partially or completely.
ROLLING CODE mode.
|
 |
RXP
Modular receiver with display
Modular receiver RXP, provided with display and programmable with
three functions: monostable, step-by-step (bistable) and timer.
Adding a memory module (MEM200, MEM200I, MEM1000, MEM1000I) the
system can learn from 318 up to 1000 codes of different transmitters.
A 3-digit display simplifies the programming function.
ROLLING CODE mode.
This receiver can be expanded up to 4 channels plugging-in the MLR
relay modules.
|
 |
MEM1000 - MEM200
Plug-in memory modules
MEM200: allows to store up to 318 different codes.
MEM1000: allows to store up to 1000 different codes.
As regards the versions MEM200-I and MEM1000-I it is possible to
attach a description of 10 characters to each stored code.
|
 |
MLR
Relay module for RXP
MLR: Relay module to expand the RXP receiver up to 4 channels.
|
 |
RXP2S220
2 channels receiver with 230V power supply
It deals with a 230V 2-channels receiver that can control loads up
to 1500W.
Ideal to switch lights on.
The radio self-learning system allows you to store up to 83 codes
of different remote controls.
The two relay outputs can be programmed with the following functions:
monostable, step-by-step and timer function as well.
ROLLING CODE mode.
|
 |
PROG2
Portable programmer
The PROG2 programmer allows:
Programming TSP-4, TRP-4, TXP-2 and TXP-4 blank transmitters with
random codes.
Programming the TSR-4 transmitters of the ROYAL PLUS series.
Connecting memory module (MEM200, MEM200I, MEM1000 and MEM1000I)
and receivers of the Personal Pass series in order to visualize,
modify, erase (partially or completely) the stored codes.
Copying the entire content of a memory module or receiver in a device
of the same model or higher.
Connecting to the PC interfacing the WINPPCL software and overseeing
the whole installation procedure.
|
 |
FASTPROG
Fast programmer for Handy and Duetto transmitters.
Serialize transmitters HANDY and DUETTO, without taking the card out
of its housing. The new programmer FASTPROG.
FASTPROG is the new FAST programmer which allows the serialization
of the transmitters HANDY and DUETTO without removing the electronic
card from its housing: you just have to lay the transmitter down on
its proper dot-matrix bed and proceed with programming.
FASTPROG must be used with PROG2, connected through its proper connector
PRPG TX.
It is possible to carry out the serialization of the transmitter with
the simple support of PROG2 or with the further supervision of the
software WINPPCL.
|
 |
WINPPCL
Data Base Software
The WINPPCL software is a Data Base which allows to store, consult
and update any “Personal Pass” systems data and setups.
WINPPCL works if connected to the portable programmer PROG2 by means
of the same "serial number".
It allows the installer to save time programming all “Personal
Pass” system components without leaving his premises. "Personal
Pass" systems' setups are then easily transferred and installed
in the system by means of PROG2.
A new user is quickly enabled thanks to the possibility of creating
automatically series of random codes for the programming of blank
transmitters. To enable a new user it is sufficient, in fact, programming
a blank transmitter with one of the codes already stored in the
receiver memory.
WINPPCL even performs an automatic check of the new random codes
to avoid the duplication of already existing codes.
It allows to print all information about users, transmitters, receivers
and installations.
It allows, jointly with PROGTAG, the programming of VTR proximity
keys and VCR passes.
It allows to track down a transmitter within the Database viewing
the installations in which it is present.
www.v2
|
